Go back into your home only when given the all-clear. Contact your utility company for follow-up.ĥ. The first responders will treat victims and identify where the gas is coming from.Ĥ. Call 911 once everyone is outside and accounted for. Leave doors and windows open if possible.ģ. Then get all occupants and pets out of the house. Turn off the fuel-burning appliance if you can do so safely and quickly.Ģ. Replace batteries every 6 months and replace alarms every 5-7 years.ġ. Mount them on a wall where the carbon monoxide alarm beeping will be heard loudly enough to wake up everyone nearby.Ĭheck the alarm by pressing the "Test" button monthly. Have detectors installed near every sleeping area in your home, as well as in the garage, if it's attached to your house. Whether the devices are battery-operated, plug-in, or hardwired (these last two should have battery backup in case of a power outage), certification is a must.Ĭonsider installation of a combination CO/smoke alarm for extra protection. Hire a qualified electrician to install your carbon monoxide detector(s). Ventilate an attached garage properly so carbon monoxide from car exhaust does not get into your home. Have your fireplace chimney and gas dryer vent professionally cleaned every year. Never light a grill or camping stove inside, never run a portable generator indoors, and never use your gas oven to heat the house. Schedule regular appliance and change furnace filters as directed. Ensure that all combustion-powered appliances are installed by a knowledgeable person and adequately vented. Home fuels include:Ĭarbon monoxide collects when these appliances are vented incorrectly. What produces carbon monoxide in the homeĬarbon monoxide in the home is usually a byproduct of fuel-burning appliances - furnace, boiler, stovetop or oven, space heater, gas dryer, water heater, generator, and gas or wood fireplace. Get everyone to fresh air and phone 911.ĬAUTION: Refer to the manufacturer's instructions for your particular make and model to verify the pattern of sounds you will hear. The unit has detected carbon monoxide gas in your home. A loud steady alarm (not beeps or chirps) = EMERGENCY. The alarm has reached the end of its useful life and you must install a new one.Ĥ. Five beeps, at 15-minute intervals = END OF LIFE. Contact the manufacturer or the retailer where you purchased the alarm.ģ. Three beeps, at 15-minute intervals = MALFUNCTION. The battery for your alarm is wearing out. One beep, at 15-minute intervals = LOW BATTERY. I spoke with a representative of First Alert about how to interpret your carbon monoxide alarm beeping or chirping. What a carbon monoxide alarm beeping means Learn what the different sounds mean and then educate your whole household. or you and your family face a life-threatening emergency. Installing a CO alarm is the best way to detect this "silent killer," and the noises it makes will tell you whether the alarm simply needs maintenance. Inhaling high levels of carbon monoxide (CO) can cause brain damage or death, yet the gas is odorless, colorless, and tasteless. Different patterns of beeps or chirps mean different things, though all signal that you must take some action. For more options, check our smoke and CO detector ratings and our smoke and CO detector buying guide.When you hear your carbon monoxide alarm beeping, the first thing you should do is pay attention to the exact nature of the sound. Here, you’ll find some of the top picks from our tests, listed in alphabetical order. Then it may be time for new smoke alarms. A small connector at the back of each alarm can be unclipped to let you safely remove it from the network. If all of that fails, your ultimate solution may be to disconnect the smoke alarms and remove their backup batteries one by one. If that doesn’t work, flipping the circuit breaker off and back on might stop the noise. First, try the reset button on each smoke alarm. If your smoke alarm has a lithium battery that you can’t take out, muffle it in a blanket, under a sofa cushion, or in your freezer until it stops.Īs for hardwired smoke alarms, “they’re interconnected through the electrical wires, so if one smoke alarm sounds, they’ll all sound, and it can be difficult to figure out what’s going on,” Deitrick says. If that doesn’t work, take the smoke alarm down. Your first step is to find the device that’s going off and reset it by pressing and holding the reset button. Your approach will vary based on the type of power your smoke alarm uses.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |